CineSticks N1 - WS - ScottyMakesStuff
CineSticks N1 - WS - ScottyMakesStuff



CineSticks N1 - WS

SKU: CS-N1-WS3
정가 $89.70 USD 판매 가격$71.76 USD 구하다 20%
/
배송 체크아웃 시 계산됩니다.

상자 수량
  • 빠른 배송
  • 재고 있음, 배송 준비 완료
  • 도중에 인벤토리

CineSticks N1의 도매 팩(3~175개)

호환 가능:

DJI RC-N1(Mini 2, Air 2, Air 2s 등) | DJI 스마트 컨트롤러 | M300 엔터프라이즈 스마트 컨트롤러 | 매빅 미니 | 미니 SE | 매빅 에어 | 매빅 2 시리즈* | 에보 나노+ | 에보 라이트+

원래 CineStick R2를 대체하는 부드럽고 단단한 고무 부츠를 제공하는 새로운 업그레이드 버전

CineSticks는 특수 설계를 사용하여 표준 소형 조이스틱으로는 할 수 없는 부드러운 제어를 제공하는 저항성 조이스틱입니다.

표준 조이스틱으로는 피하기 힘든 작은 흔들림 없이 팬, 돌리, 틸트, 트럭과 같은 영화 같은 움직임을 구현할 수 있습니다.


우리는 당신이 꿈꾸던 부드러운 움직임을 제공하기 위해 특수하고 매우 부드러운 실리콘 고무를 사용합니다. 하지만 그게 다가 아닙니다. 우리는 부드러운 제어에서 매우 단단한 제어까지 사용자를 조정 가능한 저항으로 만들었으며 조정하기가 매우 쉽습니다.

CineSticks는 Standard와 Long의 두 가지 길이로 제공됩니다. Long CineStick을 고려하고 있다면 "CineStick의 크기는 무엇입니까?" 섹션을 읽으십시오. 각각의 사용 유형을 이해하려면 아래를 참조하세요.

그렇다면 왜 우리는 이러한 촉감이 좋고 작은 조이스틱을 가지고 있는 것일까요?

드론 비행이 처음 시작되었을 때 대부분은 수제 FPV 드론이었고 경주 시에는 마이크로초 단위로 회전할 수 있어야 했기 때문에 그러한 터치 조이스틱이 있는 것이 합리적이었습니다.

불행히도 드론 제조업체의 누구도 표준 소비자 드론(시네마 드론)에 적합한 종류의 조이스틱을 고려하지 않았기 때문에 이러한 부적절한 스틱으로 묶였습니다.

우리의 CineSticks는 영화 모션에 적합할 뿐만 아니라 매우 신중하고 부드러운 모션 덕분에 드론을 처음 접하는 사람들이 훨씬 더 빨리 상황을 파악할 수 있다는 것을 알게 되었습니다.

이들은 표준 소비자 드론(시네마 드론)용으로 제작되었으며 FPV 드론에는 실제로 적합하지 않습니다. 표준 4mm 나사를 사용하여 부착합니다.


어떤 크기의 CineStick?

CineSticks가 들어옵니다. 정기적인 그리고 품종.

그만큼 정기적인 CineStick은 지금까지 가장 인기가 있으며 엄지, 핀치 또는 수정된 엄지 방법을 사용하여 스톡 조이스틱과 유사하게 사용할 수 있기 때문입니다.

위에서 언급한 수정된 엄지손가락 방법은 엄지손가락이 위에 있는 CineSticks 주위에 포인터 손가락을 얹습니다. 이것이 최상의 전체 제어를 제공한다는 것을 알았습니다.

그만큼 CineStick은 더 세밀한 제어를 제공하지만 몇 가지 중요한 제한이 있기 때문에 좀 더 전문화되어 있습니다. 손이 큰 사람을 제외한 대부분의 조종사는 컨트롤러를 거치하고 Long CineSticks를 꼬집는 것이 어렵다는 것을 알게 될 것입니다. 이러한 이유로 Long CineStick은 일반적으로 평평한 표면에서 컨트롤러와 함께 사용되거나 넥 스트랩 또는 삼각대에 장착되는 것과 같이 자체적으로 지지됩니다. 이렇게 하면 컨트롤러 상단에 손을 대고 고정할 수 있는 견고한 기반을 제공하여 긴 CineStick을 사용할 수 있습니다.

그만큼 콤보 1의 그리고 1 정기적인 Cinestick은 일반 CineStick 측면 손이 컨트롤러 무게의 대부분을 지탱할 수 있도록 절충안을 제공하므로 Long CineStick은 컨트롤러에 손의 측면을 올려 놓아 긴 CineStick을 사용할 수 있습니다. 여전히 최상의 제어를 위해 부분적으로 또는 완전히 지원되는 컨트롤러와 함께 사용하는 것이 좋습니다.

사용하는 방법

컵 스타일 마운트는 아래를 참조하십시오.

CineSticks를 부착하려면 먼저 4mm 볼트가 돌출된 상태에서 볼트가 완전히 풀렸는지 확인합니다. 실리콘 고무의 목 부분을 잡고 끝까지 멈출 때까지 스틱을 풉니다(반시계 방향). 그런 다음 회전이 멈출 때까지 고무 넥과 조이스틱 나사 구멍에 시계 방향으로 나사를 조입니다. 이 시점에서 원하는 저항에 도달할 때까지 시계 방향으로 나사를 계속 조이면 됩니다.

견고성/저항성을 높이려면, 조이스틱을 조이면 됩니다. 저항을 부드럽게/감소시키려면 실리콘 고무의 목을 잡고 스틱의 나사를 푸십시오. 고무 캡과 스틱 사이에 틈이 없도록 고무를 위로 당겨야 합니다.

CineSticks를 제거하려면 실리콘 고무의 목을 잡고 고무 나사를 몇 번 풀어서 제거하면 됩니다.

메모: CineSticks를 사용할 때, 특히 높은 저항에서 조이스틱을 놓으면 정확히 중앙으로 돌아오지 않을 수 있습니다. 대신 CineSticks를 다시 중앙으로 가져온 다음 드리프트가 없는지 육안으로 확인해야 합니다. 비행 전 스틱 검사를 수행하는 컨트롤러의 경우 저항을 높이기 전에 낮은 저항에서 CineSticks로 시작하는 것이 가장 좋습니다. CineSticks의 성능을 최상의 상태로 유지하려면 저항을 끈 상태로 CineSticks를 보관하는 것이 좋습니다.

호환성:

CineSticks는 많은 착탈식 조이스틱이 하는 것과 같은 방식으로 4mm 나사 구멍에 부착됩니다.

의심할 여지 없이 다음 목록보다 더 많은 호환 컨트롤러가 있습니다. 이것들은 우리가 지금까지 테스트한 컨트롤러일 뿐입니다.

호환 가능;

Mavic 3 Standard, Mini 2, Mavic Air 2, Air 2S와 함께 제공되는 DJI의 표준 밝은 회색 RC-N1 컨트롤러입니다. 또한 DJI 스마트 컨트롤러(현재 모델 CP.MA.00000080.01), M300 엔터프라이즈 스마트 컨트롤러.

제공된 컵 마운트 어댑터 사용과 호환 가능;

Mavic Mini 1, Mini SE, Mavic Air, 스마트 컨트롤러가 포함된 Mavic 2 Pro(이 컨트롤러에는 두 가지 부착 유형이 모두 포함되어 있으므로 스틱을 확인하여 확인) ,매빅 2 시리즈

    다른 모든 컨트롤러의 경우 위의 정보를 참조하여 컨트롤러에 설명된 대로 나사를 풀 수 있는 조이스틱이 있는지 확인하십시오.

    어떤 마운트 스타일이 있는지 어떻게 알 수 있습니까?

    CineSticks-컵 마운트 어댑터(7월 27일 모든 CineSticks와 함께 한 쌍으로 제공됨)는 CineSticks(볼트 조이스틱 마운트의 현재 DJI 4mm 나사 기반)를 내부 M6x0.75mm가 있는 이전 컵 스타일 마운트에 연결합니다. Mavic 2 시리즈 및 Mini 1과 같은 스레드.


    현재 DJI M4 나사 유형 조이스틱 - Cinesticks가 이 유형의 조이스틱을 직접 대체합니다. CineSticks와 함께 작동하려면 컵 마운트 어댑터가 필요한 이전 DJI 컵 스타일 내부 M6x0.75 스레드 - 위와 같음

    사용하는 방법

    컵 마운트 어댑터를 부착하려면 먼저 현재 컵 스타일의 조이스틱을 제거하십시오. 더 큰 구멍이 있는 컵 마운트 어댑터의 끝을 잡고 단단히 고정될 때까지 손가락으로 조입니다. 그런 다음 CineStick을 어댑터 상단에 직접 부착합니다.

    다운로드:

    CineSticks 사용 설명서

    CineSticks 지침 - 이탈리아어

    보증

    12 개월

    So why do we have these touchy, small joysticks?

    When drone flying first started the majority were those homemade FPV drones and when they're raced they needed to be able to turn in microseconds, so it made sense to have such touchy joysticks.

    Unfortunately, it seems that nobody at the drone manufacturers ever considered the kind of joysticks that would suit standard consumer drones (cinema drones) so we got lumped with these unsuitable sticks.

     

    Not only are our CineSticks good for cinematic motion, but due to the very deliberate and smooth motion, we've found that newcomers to droning find they can get the hang of things far quicker.

    These are made for standard consumer drones (cinema drones) and are not really suitable for FPV drones. It uses the standard 4mm screw to attach.


    How to use

    See 'Other Controllers' for Cup Style Mounts

    To attach the CineSticks, first, make sure that the bolt is fully unscrewed with the 4mm bolt protruding - Just pinch the neck of the silicone rubber and unscrew (counter-clockwise) the stick until you get to the end stop. Then pinch the rubber neck and screw (clockwise) into the joystick threaded hole until it stops turning. At this point just continue screw it (clockwise) until you get to your desired resistance.

    To increase the firmness/resistance, you just screw down the joystick. To soften/decrease the resistance, pinch the neck of the silicone rubber and unscrew the stick. You will need to pull the rubber up so there's no gap between the rubber cap and the stick.

    To Remove the CineSticks, just pinch the neck of the silicone rubber and unscrew the rubber a few times to remove it.

    Note: When using the CineSticks, particularly at high resistance, letting go of the joysticks may not return to the centre exactly. Instead, you should bring the CineSticks back to the centre and then confirm visually that there is no drift. For controllers that perform a pre-flight stick check, it’s best to start up with the CineSticks at low resistance before increasing resistance. It’s recommended that you store the CineSticks with the resistance off to keep your CineSticks performing at their best.

    How to tell which mount style you have?

    The CineSticks to Cup Mount Adapter (supplied with all CineSticks as a pair for 27th July) takes the CineSticks (based on the current DJI 4mm screw in bolt joystick mounts) and connects them to the previous cup style mounts that have an internal M6x0.75mm thread such as Mavic 2 series and Mini 1.

    Compatibility:

    The CineSticks attach into the 4mm threaded hole, the same way that many detachable joysticks do.

    There are undoubtedly more compatible controllers than the following list. These are just the controllers we've tested so far.

    Compatible with;

    DJI's standard light grey coloured RC-N1 controller that comes with the Mavic 3 Standard, Mini 2, Mavic Air 2, Air 2S. Also the DJI Smart Controller (current model CP.MA.00000080.01), M300 Enterprise Smart Controller.

    Compatible with use of the supplied Cup Mount Adapter; 

    Mavic Mini 1, Mini SE, Mavic Air, Mavic 2 Pro with Smart Controller (this controller has come with both attachment types so check your sticks to be sure) ,Mavic 2 Series 

      For all other controllers, please refer to the info above to see if the controller you have has the unscrewable joysticks as described.


      Current DJI M4 screw type joystick - Cinesticks directly replace this type of Joystick Previous DJI Cup style internal M6x0.75 Thread that requires the cup mount adapter to work with the CineSticks - as above
       

      How to use

      To attach the Cup Mount Adapter, first remove the current cup style joysticks. Take the end of the cup mount adapter with the larger opening, and screw it down with your fingers until it's firmly on. Then attach the CineStick directly to the top of the adaptor.

       


      최근 본